| |
 |
Major
Features
- Simultaneous full duplex 1 Gb/s Fibre
Channel delivers up to 200 MB/s
- Full fabric support using F_Port and FL_Port
connections
- On board hardware context cache for superior
fabric performance
- Support for concurrent use of multiple
protocols (SCSI & IP)
- Full support for FC service Class 2 and 3
- Support for FC-Tape (FC-2) devices
- 64-bit, 66 MHz PCI
- End-to-end parity protection for high data
integrity
- Buffered data architecture to support up to
100 km cabling
- Robust suite of software including IP and
storage protocols under Windows 2000, Windows
NT, HP-UX, Linux, NetWare, Solaris and AIX
- GBIC fibre optic or copper physical
interfaces
|
|
Description
The LightPulse ™ LP9000 Fibre Channel PCI
host adapter provides the flexibility and broad
interoperability needed for complex highly
scalable SANs. The LP9000 provides a unique
combination of features, including switched fabric
support using F_Port and FL_Port connections,
full-duplex data transfers, high data integrity
features, support for all Fibre Channel topologies
and support for service class 2 and 3.
The LP9000 also features sophisticated hardware
that provides superior performance in storage area
networks, delivering low latency and high
throughput in switched, arbitrated loop and
clustered environments. Support for both copper
and fiber optic cabling is provided through
standard GBIC interfaces.
The LP9000 delivers exceptional performance
through the use of Emulex’s Centaur ASIC, a 266
MIPs onboard processor and state of the art dual
ported buffer memory. The LP9000 features a
64-bit, 66 MHz PCI interface and provides the
richest set of features available.
Driver Support |
The LightPulse ™ LP9000 is complemented by a
rich suite of software support including storage
protocol (SCSI), network protocol (IP) as well as
concurrent multi-protocol (SCSI & IP)
operation, enabling advanced storage area network
(SAN) implementations in Windows 2000, Windows NT,
HP-UX, Linux, NetWare, Solaris and AIX
environments. All drivers are also fully
compatible with the Emulex LP9002L, LP8000,
LP7000E, LP952L and LP850 host bus adapters.
|
|
|
Standards
ANSI
Fibre Channel FC-FS
ANSI Fibre Channel FC-PH/PI
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
PCI Local Bus Revision 2.2
Fibre Channel Class 2, 3
PHP Hot plug - Hot swap
Gigabit Interface Converter (GBIC)
Architecture
Emulex
Centaur ASIC technology
up to 66 MHz PCI bus master DMA
512 KB FLASH memory
1 MB code RAM
256 KB buffer RAM
Software Environments
Windows
2000
Windows NT
Linux
HP-UX
NetWare
Solaris
AIX
Hardware Environments
x86,
SPARC and PowerPC
3.3 or 5V tolerant signaling
Copper
| Data
Rate: |
1.0625
Gb/s |
| Cable
Type: |
Dual
Twinax or Quad Axial |
| Connector
Type: |
DB9 |
| Distance: |
30
meters (98') |
Optical
| Data
Rates: |
1.0625
Gb/s |
| Optics: |
short/long
wave lasers |
| Cable: |
9/125
µm single-mode fiber |
| |
50/125
µm multi-mode fiber |
| |
62.5/125
µm multi-mode fiber |
| Connector
Type: |
dual
SC |
| Distance: |
10K
meters (32,800')
9/125 µm fiber |
| |
500
meters (1640')
50/125 µm fiber |
| |
300
meters (984')
62.5/125 µm fiber |
|
Physical Dimensions
Short
PCI form factor
174.75mm x 106.68mm
(6.88" X 4.20")
Power Requirements
| Volts: |
+5
VDC +/- 5% |
| Power |
10
watts typical |
Environmental Conditions
| Operating
Temperature, ambient: 0° to 45° C (32°
to 113° F) |
| Storage
Temperature:-10° to 55° C (14° to 131°
F) |
| Relative
Humidity: 5% to 95% non-condensing |
Agency Approvals
| Class
1 Laser Product per DHHS 21CFR (J) and
EN60825 |
| UL
Recognized to UL 1950 |
| CUR
Recognized to CSA22.2, No. 950 |
| TUV
Certified to EN60950 |
| FCC
Rules, Part 15, Class B |
| ICES-003,
Class B |
| EMC
Directive 89/336/EEC (CE Mark) |
| -
EN55022, Class B |
| -
EN55024 |
| Australian
EMC Framework (C-Tick Mark) |
| -
AS/NZS 3548, Class B |
| VCCI,
Class B |
|
Ordering Information
| LP9000-T1 |
Copper
DB9 GBIC interface |
| LP9000-N1 |
Multi-mode
optic GBIC interface |
| LP9000-L1 |
Single-mode
optic GBIC interface |
|
|
|
|
|
|