[lmenu.htm]

 

[tmenu.htm]
  






Major Features
  • Simultaneous full duplex 1Gb/s fibre channel delivers up to 200 MB/s
  • Full fabric support using F_Port and FL_Port connections
  • On board hardware context cache for superior fabric performance
  • Support for concurrent use of multiple protocols (SCSI & IP)
  • Full support for FC service Class 2 and 3
  • Support for FC-Tape (FC-2) devices
  • 64-bit, 33 MHz PCI
  • End-to-end parity protection for high data integrity
  • Buffered data architecture to support up to 100 km cabling
  • Robust suite of software including IP and storage protocols under Windows 2000, Windows NT, HP-UX, Linux, NetWare, Solaris and AIX
  • GBIC or embedded physical interfaces

Description

The LightPulse™ LP8000 fibre channel PCI host bus adapters deliver exceptional performance through the use of Emulex’s Dragonfly ASIC, a 266 MIPs onboard processor and state of the art dual-ported buffer memory. The LP8000 features a 64-bit PCI interface and provides the richest set of features available.

The LP8000 is designed to support mission-critical enterprise applications. The LP8000 provides a unique combination of features, including switched fabric support using F_Port and FL_Port connections, full-duplex data transfers, high data integrity features, support for all fibre channel topologies and support for service class 2 and 3.

The LP8000 also features sophisticated hardware that provides superior performance in storage area networks,delivering low latency and high throughput in switched,arbitrated loop and clustered environments.Support for both copper and fiber optic cabling is provided through standard GBIC or embedded interfaces.

Driver Support |

The LightPulse™ LP8000 is complemented by a rich suite of software support including storage protocol (SCSI), network protocol (IP) as well as concurrent multi-protocol (SCSI & IP) operation, enabling advanced storage area network (SAN) implementations in Windows 2000, Windows NT, HP-UX, NetWare, Solaris and AIX environments. All drivers are also fully compatible with the Emulex LP9002L, LP9000, LP7000E, LP952L and LP850 host bus adapters.


Standards

ANSI Fibre Channel FC-PH
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
PCI Local Bus Revision 2.1
Fibre Channel Class 2, 3
PHP Hot plug - Hot swap
Gigabit Interface Converter (GBIC)

Architecture

Emulex Dragonfly ASIC technology
up to 33 MHz PCI bus master DMA
512 KB FLASH memory
1 MB code RAM
256 KB buffer RAM

Software Environments

Windows 2000
Windows NT
NetWare
HP-UX
Linux
Solaris
AIX

Hardware Environments

x86, SPARC and PowerPC
PCI hardware platforms
5V signaling

Copper
Data Rate: 1.0625 Gb/s
Cable Type: Dual Twinax or Quad Axial
Connector Type: DB9
Distance: 30 meters (98')
Optical
Data Rates: 1.0625 Gb/s
Optics: short/long wave lasers
Cable 9/125 µm single-mode fiber
  50/125 µm multi-mode fiber
  62.5/125 µm multi-mode fiber
Connector Type: dual SC
  10K meters (32,800') 9/125 µm fiber
  500 meters (1640') 50/125 µm fiber
  300 meters (984') 62.5/125 µm fiber
Physical Dimensions

Short PCI form factor
174.75mm x 106.68mm
(6.88" X 4.20")

Power Requirements
Volts: +5 VDC +/- 5%
Power 10 watts typical
Environmental Conditions
Operating Temperature: 0° to 45°C (32° to 113°F)
Storage Temperature: -10° to 55°C (14° to 131°F)
Relative Humidity: 5% to 95% non-condensing
Agency Approvals
Class 1 Laser Product per DHHS 21CFR (J) and EN60825
UL Recognized to UL 1950
CUR Recognized to CSA22.2, No. 950
TUV Certified to EN60950
FCC Rules, Part 15, Class B*
ICES-003, Class B*
EMC Directive 89/336/EEC (CE Mark)
  - EN55022, Class B*
  - EN50082-1
Australian EMC Framework (C-Tick Mark)
   AS/NZS 3548, Class B*
VCCI, Class B*

*Note LP8000-D1 is a Class A
Ordering Information
LP8000-D1 Embedded copper DB9 interface
LP8000-F1 Embedded multi-mode optic interface
LP8000-T1 Copper DB9 GBIC Interface
LP8000-N1 Multi-mode optic GBIC Interface
LP8000-L1 Single-mode optic GBIC Interface
[botmenu.htm]