| |
 |
Major
Features
- Simultaneous full duplex 1Gb/s Fibre Channel
delivers up to 200 MB/s
- Full fabric support using F_Port and FL_Port
connections
- On board hardware context cache for superior
fabric performance
- Support for concurrent use of multiple
protocols (SCSI & IP)
- Full support for FC service Class 2 and 3
- Support for FC-Tape (FC-2) devices
- 32-bit, 33MHz PCI
- End-to-end parity protection for high data
integrity
- Buffered data architecture to supportu to
100 km cabling
- Robust suite of software including IP and
storage protocols under Windows 2000, Windows
NT, HP-UX, Linux, NetWare, Solaris and AIX
- GLM physical interfaces
|
|
Description
The LightPulse ™LP7000E fibre channel PCI
host bus adapters deliver exceptional performance
through the use of Emulex ’s Superfly ASIC, a
266 MIPS onboard processor and high speed buffer
memory. The LP7000E features a 32–bit PCI
interface and provides the richest set of features
available.
The LP7000E is designed to support
mission-critical enterprise applications. The
LP7000E provides a unique combination of features,
including switched fabric support using F_Port and
FL_Port connections, full-duplex data transfers,
high data integrity features, support for all
fibre channel topologies, and support for service
class 2 and 3.
The LP7000E also features sophisticated
hardware that provides superior performance in
storage area networks, delivering low latency and
high throughput in switched, arbitrated loop and
clustered environments. Support for fiber optic
cabling is provided through standard GLM physical
interfaces.
Driver Support |
The LightPulse™ LP7000E is complemented by a
rich suite of software support including storage
protocol (SCSI), network protocol (IP) as well as
concurrent multi-protocol (SCSI & IP)
operation, enabling advanced storage area network
(SAN) implementations in Windows 2000, Windows NT,
HP-UX, Linux, NetWare, Solaris and AIX
environments. All drivers are also fully
compatible with the LP9002L, LP9000, LP8000,
LP8000S, LP952L and LP850 host bus adapters.
|
|
Standards
ANSI
Fibre Channel FC-PH
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
FCSI 301 Revision 2.2 Gigabaud Link Module
PCI Local Bus Revision 2.2
Fibre Channel Class 2, 3
Architecture
Emulex
Superfly ASIC technology
up to 33 MHz PCI bus master DMA
512 KB FLASH memory
512 KB code RAM
256 KB buffer RAM
Software Environments
Windows
2000
Windows NT
Linux
HP-UX
NetWare
Solaris
AIX
Hardware Environments
x86,
SPARC, PowerPC and Alpha
PCI hardware platforms
Optical
| Data
Rates: |
1.0625
Gb/s |
| Optics: |
short/long
wave lasers |
| Cable: |
9/125
µm single-mode fiber |
| |
50/125
µm multi-mode fiber |
| |
62.5/125
µm multi-mode fiber |
| Connector
Type: |
dual
SC |
| |
10
K meters (32,800') 9/125 µm fiber |
| |
500
meters (1640' ) 50/125 µm fiber |
| |
300
meters (984' ) 62.5/125 µm fiber |
|
Physical Dimensions
Short
PCI form factor
174.75mm x 106.68mm
(6.88" X 4.20")
Power Requirements
| Volts: |
+5
VDC +/- 5% |
| Power |
8
watts typical |
Environmental Conditions
| Operating
Temperature: |
0°
to 45° C (32° to 113° F) |
| Storage
Temperature: |
-10°
to 55° C (14° to 131° F) |
| Relative
Humidity: |
5%
to 95% non-condensing |
Agency Approvals
| Class
1 Laser Product per DHHS 21CFR (J)
& EN60825 |
| UL
Recognized to UL 1950 |
| CUR
Recognized to CSA22.2, No. 950 |
| TUV
Certified to EN60950 |
| FCC
Rules, Part 15, Class B |
| ICES-003,
Class B |
| EMC
Directive 89/336/EEC (CE Mark) |
| -
EN55022, CISPR22/85, Class B |
| -
EN50082-1 |
| Australian
EMC Framework (C-Tick Mark) |
| -
AS/NZS 3548, Class B |
| VCCI,
Class B |
Ordering Information
| LP7000E-N1 |
Multi-mode
optic GLM interface |
| LP7000E-L1 |
Longwave
GLM interface |
|
|
|
|
|
|
|